PRODUCTS CENTER

E-mail: [email protected]

big diameter sae 100r4 hose

SAE 100R Hose Data | PipeandHose

SAE 100R series Description 100R1 Steel wire reinforced, rubber covered hydraulic hose (one wire braid) Type A - Thick cover (skive type) Type AT - Thin cover (no-skive type) 100R2 High pressure, steel wire reinforced, rubber covered hydraulic hose (two wire braid)

J517A: Hydraulic Hose - SAE International

2016/12/15· Rationale: General revision of SAE J517 to add a workmanship clause to Wire Inserted Hydraulic Suction Hose (SAE 100R4) Paragraph 19.5 workmanship clause to ensure that the internal wire is clipped sufficiently back far enough for handling of the hose.

3/4"ID x 50'' MSHA Accepted SAE 100R4 300psi Hydraulic Hose …

Hydraulic Hose. Working Pressure. 300 psi. Product Weight. 0.44. UOM. package of 50. Notes. SAE 100R4Inner Tube: Nitrile Blend Reinforcement: 3/4" - 1-1/2" 1 helical cabled wire and 1 fiber braid 2"- 1 helical, single-stranded wire and 1 fiber braid Cover: Neoprene Temperature Range: -40°F to +212°F (-40°C to +100°C) Hose Ends: Coll-O-Crimp

SAE 100R5 DOT Hose | Hose and Fittings Source

Hose Ratings include: SAE 100R5 SAE J1402 type AII SAE J1402, DOT FMVSS 106 AII for Truck Air Brake (-04 thru -12) SKU ID Inch OD Inch Working psi Min Burst psi Min Bend Radius Inch Weight (lbs per foot) 04R5 3/16 0.52 3,000 12,000 3.0 0.15 05R5

GMV Global MegaVac® Return Line and Suction Hose - SAE 100R4 …

Outside Diameter (in) Outside Diameter (mm) Features. Features and Benefits. Uses a helical spiral-wire to prevent hose collapse under suction. Meets marine ABS and DNV-GL with use of HeatGuard high temp sleeve. Meets Flame Resistance Acceptance Designation MSHA 2G. Standards: SAE 100R4. Cover: MSHA approved.

Hydraulic hose - SAE standards | Hydraulics & Pneumatics

2003/11/1· Hydraulic hose - SAE standards. Nov. 1, 2003. SAE hydraulic hose standards — SAE 100R1 hose should be used with petroleum- and water-based hydraulic fluids, within a temperature range from140° to 100° C. Type A - Consists of an inner tube of oil-resistant

Hose HOSE - Parker Hannifin

SAE 100R4 Transportation Hose SAE J1402 Al Air Brake Hose SAE J1402 A Liquefied Petroleum Gas SAE J2064 TYPE C Push-Lok Hose Outer Diameter A critical measurement when considering hose clamps and appliions where envelope size is Is the

Medium Pressure Suction and Return Line Hoses - SAE 100R4 - …

Parker''s Medium Pressure No-Skive Suction and Return Line Hose 811S has been designed with an Isobaric 1.0 MPa for all sizes and a temperature range from -40 C up to +100

Hydraulic hose - SAE standards | Hydraulics & Pneumatics

2003/11/1· Hydraulic hose - SAE standards. Nov. 1, 2003. SAE hydraulic hose standards — SAE 100R1 hose should be used with petroleum- and water-based hydraulic fluids, within a temperature range from140° to 100° C. Type A - Consists of an inner tube of oil-resistant

Hydraulic hose - SAE standards | Hydraulics & Pneumatics

2003/11/1· Hydraulic hose - SAE standards. Nov. 1, 2003. SAE hydraulic hose standards — SAE 100R1 hose should be used with petroleum- and water-based hydraulic fluids, within a temperature range from140° to 100° C. Type A - Consists of an inner tube of oil-resistant

Hydraulic Hose: SAE J517 100R3, 100R4, 100R5, 100R6

Hydraulics hose SAE J517 100R4 Size (Inch) Inside Diameter Reinforcement Outside Diameter Proof Pressure Working Pressure Burst Pressure Bend Radius Basic (mm) Tolerance Plus (mm) Tolerance Minus (mm) Min (mm) Max (mm) Max (mm) Min (mm) (Mpa)

The Complied World of SAE Standards | Parker Hose Products

2017/7/13· Parker Hose Products Division has a full line of hydraulic hoses designed for one-half SAE bend radius at full SAE pressure, which exceeds the minimum bend radius. For example, the bend radius of Parker’s 797 hydraulic hose is half of SAE’s 100R1, 100R2, 100R4, 100R12 and 100R13 minimum requirement, which reduces hose length requirements by up to 47%.

Parker 811 Suction and Return Hose - MFCP

811 | Parker Suction Hose. Up to one-half the SAE minimum bend radius for standard and high-temperature appliions. Meets or exceeds SAE 100R4 requirements. Compatible with Parkrimp or field attachable fittings. High-visibility layline. Suitable for vacuum appliions from 25 to 28 in/Hg. Oil- and weather-resistant synthetic rubber cover.

SAE 100R4 Suction and Return Hose

SAE 100R4 Suction and Return Hose Recommended for hydraulic suction and return lines. Helical wire prevents collapse under vacuum up to 25"/hg. Inner tube: Oil-resistant synthetic rubber SAE 100R4 Suction and Return Hose is recommended for low pressure or vacuum lines in hydraulic system service with petroleum and water-base fluids.

HYDRAULIC OIL SUCTION AND DELIVERY HOSE SAE 100R4 | …

HYDRAULIC OIL SUCTION AND DELIVERY HOSE SAE 100R4 Suction and delivery hose for hydraulic oils Tubi Gomma Torino, leading manufacturer of industrial rubber hoses, has been active on the Italian and international markets for more than 60 years.

Dash Sizing for Hoses and Tubes Explained - MFCP

Each dash size corresponds to a progressively larger diameter, measured in sixteenths of an inch. “-1” is 1/16, “-2” is 2/16, and so on. In this case, -6 hose would indie a hose with an inside diameter of 6/16”, or 3/8". In another example, a -10 tube would indie a tube with an outside diameter of 10/16", or 5/8".

Hydraulic oil hose SAE/100/R4 IVG Colbachini

Specifiions. SAE J517, type SAE 100 R4. Appliion. hardwall hose used for the suction and delivery of oil in hydraulic systems. Temperature: from -40°C (-40°F) to +100°C (+212°F). Branding: continuous eossed marking “IVG SAE 100 R4 / quarter and year of production”.

J517A: Hydraulic Hose - SAE International

2016/12/15· Rationale: General revision of SAE J517 to add a workmanship clause to Wire Inserted Hydraulic Suction Hose (SAE 100R4) Paragraph 19.5 workmanship clause to ensure that the internal wire is clipped sufficiently back far enough for handling of the hose.

Low Pressure Hydraulic Hose available in Various Sizes

Table 1: SAE 100R4 Wire Inserted Hydraulic Suction Hose Technical Specifiion Item Size SAE Size I.D. O.D. Max. W.P. Proof Pressure P.P. Min. B.P. Min. B.R. Weight mm inch dash min. max. max. MPa psi MPa psi MPa psi mm kg/m SAER4-01 19 3/4-12

C5C Hydraulic Hose - SAE 100R5 (Gates) - Hoses & Fittings - …

This hose meets or exceeds requirements of SAE 100R5 for traditional hydraulic appliions, DOT FMVSS 106-74 Type All and SAE J1402 Type All for air brake appliions (-4 to -12). Not recommended for gasoline or diesel. Reinforcement: One braid of high-tensile carbon steel wire over one braid of polyester. Temperature Range: Under SAE 100R5

Three Key Words in Hydraulic Hose Sizing: I.D., Dash Size and …

2017/8/17· Inner diameter (I.D.) is the span of the empty space in a circular hose cross-section that affects the flow velocity of the fluid within the hose. A hose with an oversized I.D. will result in sluggish system performance, while an undersized I.D. can cause …

C5C Hydraulic Hose - SAE 100R5 (Gates) - Hoses & Fittings - …

This hose meets or exceeds requirements of SAE 100R5 for traditional hydraulic appliions, DOT FMVSS 106-74 Type All and SAE J1402 Type All for air brake appliions (-4 to -12). Not recommended for gasoline or diesel. Reinforcement: One braid of high-tensile carbon steel wire over one braid of polyester. Temperature Range: Under SAE 100R5

Hydraulic Megastore - 100 R7 Thermoplastic Hose - EN 855 - SAE …

External covering: Polyurethane, black, pinpricked, white ink-jet branding. Applicable specs: Exceeds SAE 100 R7. Recommended fluid: Hydraulic fluid ptroleum based, glicol-water based lubricant. Operating temperature range: From -40°C to +100°C continuous +70°C for water based fluids. Price shown is per metre of hose.

SAE 100R Hose Data | PipeandHose

SAE 100R series Description 100R1 Steel wire reinforced, rubber covered hydraulic hose (one wire braid) Type A - Thick cover (skive type) Type AT - Thin cover (no-skive type) 100R2 High pressure, steel wire reinforced, rubber covered hydraulic hose (two wire braid)

Hydraulic Hose: SAE J517 100R3, 100R4, 100R5, 100R6

Hydraulics hose SAE J517 100R4 Size (Inch) Inside Diameter Reinforcement Outside Diameter Proof Pressure Working Pressure Burst Pressure Bend Radius Basic (mm) Tolerance Plus (mm) Tolerance Minus (mm) Min (mm) Max (mm) Max (mm) Min (mm) (Mpa)

SAE 100R4 Suction and Return Hose

SAE 100R4 Suction and Return Hose Recommended for hydraulic suction and return lines. Helical wire prevents collapse under vacuum up to 25"/hg. Inner tube: Oil-resistant synthetic rubber SAE 100R4 Suction and Return Hose is recommended for low pressure or vacuum lines in hydraulic system service with petroleum and water-base fluids.

Parker 811 Suction and Return Hose - MFCP

811 | Parker Suction Hose. Up to one-half the SAE minimum bend radius for standard and high-temperature appliions. Meets or exceeds SAE 100R4 requirements. Compatible with Parkrimp or field attachable fittings. High-visibility layline. Suitable for vacuum appliions from 25 to 28 in/Hg. Oil- and weather-resistant synthetic rubber cover.

Hydraulic Hose | SAE 100R4

Find out more about our SAE 100R4 hydraulic hose, with steel wire reinforcement. Available from 19mm to 152mm, order online now for low prices & next day delivery. egories egories ABS ABS ABS Pipe Inch ABS Pipe Fittings Inch ABS Flanges Inch

Stems and Ferrules for SAE 100R4 Hose

22 Ferrules for SAE 100R1, 100R1AT, 100R2, 100R2AT, 100R3, 100R4, 100R5, Hydra-Lite I & II1 & 2 WIRE COINATION STAINLESS STEEL TYPE 303 FERRULE– SKIVE REQUIRED for SAE 100R1, 100R2, 100R3, Hydra-Lite I & II Part Hose Nuer I.D. -L

SAE 100R5 DOT Hose | Hose and Fittings Source

Hose Ratings include: SAE 100R5 SAE J1402 type AII SAE J1402, DOT FMVSS 106 AII for Truck Air Brake (-04 thru -12) SKU ID Inch OD Inch Working psi Min Burst psi Min Bend Radius Inch Weight (lbs per foot) 04R5 3/16 0.52 3,000 12,000 3.0 0.15 05R5